How To Reset Tire Pressure Sensor On 2008 Chevy Silverado – TPMS Reset

You must be familiar with the TPMS of the vehicle, which indicates the Tire Pressure Monitoring System. The system’s job is to alert for any trouble inside the vehicle.

Recently, your 2008 Chevy Silverado has started to show some difficulties that resemble tire pressure system problems. So you must be searching for “how to reset tire pressure sensor on 2008 Chevy Silverado.” As a result, you can employ the tire iron to remove the lug nuts, get the paperclip, look for the reset button, and make sure you press and keep it for 5 seconds.

It’s not safe to ride with the TPMS signal illuminated. So, whenever you notice any warning sign, make sure you give it a proper reset. And if you want to learn the easy methods for resetting, this article will guide you to the ultimate result.

What Are The 2008 Chevy Silverado TPMS Problems That Require Reset?

Why should you reset the Silverado 2008 pressure monitoring setting? We have discovered some reasons that indicate you need a reset. So, let’s see the possible TPMS problems on your Chevy Silverado that hint you need a reset.

  • Dead or weak battery problem.
  • Wiring or antenna issue.
  • The sensor and RF module on the truck might not work.
  • Environmental issue.
  • Tire gauge difficulties.
  • Air pressure trouble.

What Is The Correct Tire Pressure For A Chevrolet?

what should the tire pressure be on a chevy silverado

We usually determine the tire pressure limit in pounds per square inch, or “PSI.” It’s a unit of pressure that specifies the amount of force present at a location. So, the tire pressure will vary and change according to the driving action.

From 2005 to 2022, Chevy vehicles suggested tire pressure ranging from 26 psi to 80 psi based on the model, equipment, tire size, or trim. However, the standard tire pressure for your Chevy Silverado should be 35 psi in the front and back.

Should All 4 Tires Have The Same PSI?

Absolutely, all of the tires should have the same psi, and you must keep everything in good order. But sometimes the four wheels might show different psi from each other.

Suppose you have a 35-psi suggestion and the maximum pressure limit specified on the side is 44 psi. So, you can keep 38 to 40 psi in the tires. Since the article is focusing on the 2008 model, you might be wondering what the tire pressure should be on a 2008 Chevrolet Silverado.

The 2008 Chevy Silverado should maintain 35 psi. Also, the matter of fact is tire pressure typically remains higher in front than the back side to take additional pressure on the engine and transmission, particularly in front-wheel drive automobiles.

2008 Silverado Tire Pressures By Size

For the convenience of Chevy Silverado 2008 users, we have made a chart of tire pressures by size. You can check it out below.

Size of TireFrontBack
LT245/70R17/C 108Q45 PSI45 PSI
P245/70R17 108S35 PSI35 PSI
P265/65R18 112S35 PSI35 PSI
P265/70R17 113S35 PSI35 PSI
P275/55R20 111S30 PSI30 PSI
LT245/75R16/E 120S50 – 65 PSI80 PSI
LT265/70R17/E 121Q60 PSI75 PSI
LT225/75R17/E 113Q65 PSI80 PSI
LT265/75R16/E 123Q60 PSI75 PSI

Where Is TPMS Reset Button On A 2008 Chevy Silverado?

Silverado tire pressure problems are common, so you might need to perform a reset. But do you know where the reset button is located?

TPMS reset buttons are often found beneath your car’s steering wheel. So turn off the car and turn the key without starting the engine. Then you can go for a reset. Actually, resetting the pressure sensor on a 2008 Chevy Silverado is a little bit tricky, but it will take at most 10 to 12 minutes at best.

How To Reset Tire Pressure Sensor On A 2008 Chevy Silverado Without A Tool

2008 silverado tpms reset without tool

Usually, TPMS systems are tricky to troubleshoot without the help of a normal mechanic. Therefore, a professional’s hand is always preferable. When you have scan tools, TPMS trigger tools, or relearn tools, your job will be much easier. So, if you discover a light on your vehicle that signals a tire pressure problem, take immediate action to give the 2008 Silverado TPMS a reset.

But how do we turn off your tire pressure sensor on the 2008 Chevy Silverado? Below we have the step-by-step guidelines for giving a reset without using tools.

Step 1

First, you have to switch the ignition key to the “ON” position without starting your car engine. If you have the ignition switch, push the engine start or stop button without the brake pedal. Plus, don’t forget to park the Chevy Silverado on flat ground.

Step 2

Take five seconds and press the lock and unlock buttons on your RKE, or remote keyless entry, transmitter. You will probably hear the horn sound two times, and the tire learning active message will come.

Step 3

Also, you have to turn on the sensor. Start with the driver-side front tire, detach the valve cover, and increase or decrease your tire’s air pressure unless you notice any horns.

Step 4

It’s time to repeat the driver’s side front, back front, and passenger side back tires. And you’ll be done with the resetting part after hearing the horn one more time.

Step 5

Now, turn off the ignition, and the active tire learning reading will go away. Additionally, adjusting your tire pressure according to the user manual is what’s left now. And you are done with the 2008 Silverado TPMS reset without a tool.

How Do You Reset TPMS Without Reset Button – 9 Easy Tips

You can easily reprogram your tire sensor just by following the given tips. So, don’t miss out on any of our given instructions.

  1. While doing this job, take at least 10 minutes and drive above 50 mph; your car will possibly stop flashing the light. But if not, then do the process almost identically to the previous steps we talked about.
  2. Before starting your automobile, set the ignition key to the “ON” setting.
  3. Press the TPMS reset option 3 times unless your light blinks 3 times.
  4. Now, start the engine and wait for the pressure sensor to refresh within 20 minutes.
  5. You can also reset the trip odometer by pushing the odometer reset stem until you notice the tire pressure level is visible.
  6. Now, you can also increase the car’s tires to three psi higher than the recommended 35 psi. Then release them entirely.
  7. Then, ensure that you do it for the spare tire as well, since it may contain a sensor.
  8. You’ll also have to disconnect the positive battery cable when the car is turned off. The step will ensure you reset the clock, memory, and other electrical features to their default settings.
  9. After that, switch on the vehicle and sound the horn for at least 3 seconds. It will ensure you have discharged all remaining power, and it should also reset the sensor light system when you re-engage your car battery.

Some Facts About TPMS Reset By Relearn Tool

With the help of any tool, your resetting job becomes much easier. This time we will show you how you should employ the relearn tool.

  • Simply increase the pressure on all tires and position the relearn tool against the sidewall nearest to the valve stem.
  • You actually use the tool to enable the left front vehicle sensor.
  • Hold down the unlock and lock buttons on your key fob unless you notice horn sounds.
  • After all the processes, you have to continue repeating these processes.
  • For every tire, starting from the front, then to the right back and left back.

How Much Does A 2008 Chevy Silverado TPMs Sensor Cost?

Tire pressure monitoring sensor batteries are typically designed to last ten years. But, if you need to repair it, the average cost you might have to invest in a Chevy Silverado 1500 Tire Pressure Sensor Replacement is $98 ($3 for components plus $95 for labor).

FAQ

If you don’t understand the Chevy Silverado TPMS resetting tips, we hope the frequently asked questions section will help you understand more. So, don’t overlook this part!

Do tire pressure sensors reset themselves?

The u003ca href=u0022https://madisonrising.com/subaru-tire-pressure-sensor-problem/u0022 target=u0022_blanku0022 rel=u0022noreferrer noopeneru0022u003etire pressure sensoru003c/au003e light needs to switch off automatically when you have inflated the tires.  During the rotation, straight TPMS systems immediately reset.

Can you relearn TPMS without a tool?

The vehicle relearn procedure typically has to be finished with an RPMS scan tool. In that case, the horn can be honked for around 3 seconds after starting the car. Then, reset the sensor light system after u003ca href=u0022https://madisonrising.com/car-starts-after-disconnecting-and-reconnecting-battery/u0022 target=u0022_blanku0022 rel=u0022noreferrer noopeneru0022u003ereconnecting your batteryu003c/au003e.

How to reset the tire monitor on a 2009 Silverado?

You can simply complete the resetting job of the Chevy Silverado just by following the given steps:u003cbru003e1. While not starting the car, turn the ignition u0022ON.u0022u003cbru003e2. Once the u003ca href=u0022https://madisonrising.com/how-to-reset-subaru-tire-pressure-light/u0022 target=u0022_blanku0022 rel=u0022noreferrer noopeneru0022u003etire pressure lightsu003c/au003e have flashed 3 times, make sure you push the reset button.u003cbru003e3. Then, wait for the tire sensor to re-calibrate for around 20 minutes.

How to reset a tire pressure sensor fault on a Ford?

The Ford car tire pressure system can be fixed by giving it a reset, so you can follow the given instructions.u003cbru003e1. The car’s battery should be started first.u003cbru003e2. Find the TPMS reset button under or next to your steering wheel.u003cbru003e3. Keep it unless you notice the dashboard light flashing 3 times.u003cbru003e4. The light will turn off after the release of the button, and then you can turn the key in the ignition.

Final Words

So, if you face any trouble with your 2007 to 2021 model Chevy Silverado, resetting can be the best solution, so we have shared how to reset tire pressure sensor on 2008 Chevy Silverado. Following the given steps will let you successfully fix the TPMS problems for sure.

The instructions we shared are based on the owner’s manual. Therefore, make sure you understand the signals first and then attempt to give it a proper reset to make it go into default mode. And don’t forget to ensure your Chevy Silverado has 35 to 45 PSI.

Similar Posts